Aerospace & Defense

Trilion supports the aerospace testing industry and its suppliers by providing precise part geometries and material characteristics. This data is used as input parameters for finite element simulations and flow analyses, for verification of simulations against real measurements in wind tunnels and climate chambers as well as for reverse engineering. Furthermore, optical 3D scanners are suited for quality control of complex freeform surfaces. Therefore, they are used to inspect airfoils of aircraft engines, terrestrial gas & steam turbines and turbocharging systems.

Learn More


Wind Tunnel Testing

3D scanning verifies the "as built" vs. "as designed" shape of scale models in wind tunnel testing to ensure that scaling does not cause deviations. In addition, GOM's ARAMIS high-speed deformation measurement system analyzes vibrations and deflections caused by wind load in the wind tunnel online and in real time. This makes it possible to analyze wing behavior at specific speeds and in different flight maneuvers.

Reverse Engineering

Internal and external 3D aircraft scanning supplies 3D CAD information which accurately reflects the current state of build of the airframe and ancillary equipment. The dense point cloud data represents a solid base for CAD modeling, thus allowing reliable planning of aircraft design and electronics.

Digital Assembly

Acquisition of "as built" data and reverse engineering play key roles as links between the physical and digital model environments. Full aero surfaces are vital for scale-model wind tunnel testing, CFD model creation, symmetry checks and finite element methods to ensure that computer simulations are valid.

Measuring the entire aircraft within one coordinate system also supports digital assembly, and capturing various positions of the movable control surfaces is essential to performing motion studies. Time-effective data acquisition results in cost-effective, fast and easy integration into downstream processing requirements.

Fuselage & Cabin

CFD Analysis & CAD Comparison

Computer simulations are used to optimize aircraft design during the development phase. GOM's ATOS 3D digitizer supplies dense and precise polygon mesh representations of an aircraft's "as built" condition to obtain a realistic matching CFD analysis. The 3D data is also valuable for symmetry checks and for detecting damage to working prototypes, caused for example by hard landings.

Material, Jointing & Component Testing

Optical metrology analyzes the mechanical properties and behavior of materials, joints and components. GOM's ARAMIS sensors can be integrated into existing test environments, test stands and testing machines. The non-contact sensors measure full-field 3D strain and deformation of soft and rigid materials under mechanical or thermal load. Thus conventional extensometers and strain gauges can now be replaced by GOM's real-time 3D surface deformation analysis.

FEM Deformation Verification

GOM's deformation measurement systems are widely used throughout the aerospace industry to measure and verify deformations in lightweight structures during operation. The systems are easy to integrate into test environments such as climate chambers, wind tunnels, fatigue test stands, etc. In addition, GOM software supports numerical result verification of the captured full-field 3D data.


Dynamic Deformation Measurement

Dynamic deformation measurement visualizes the behavior of aerodynamic structures in real use. During running operations, for example, real-time shape, vibration, acceleration, deformation and imbalance can be analyzed.

Space Shuttle Measurements

Trilion was called on twice to support urgent Space Shuttle program tests. In 2003-2004, we were an integral part of the Return to Flight program, after the loss of the Orbiter Columbia from a wing foam impact that had occurred at launch. ARAMIS became the required DYNA model validation tool during the extensive impact testing program. ARAMIS with high speed cameras was used at NASA Glenn in Cleveland for 6 x 6 and 6 x 12 inch coupon tests, and at Southwest Research Institute in San Antonio for full-scale wing impact tests. The images show the test setup and typical dynamic displacement results.

In 2011, Trilion was called upon to make ARAMIS measurements at Launch Complex 39A at Kennedy Space Center during a tanking test, as part of the root cause investigation for the STS-133 stringer cracking issue. This effort entailed rapid fabrication of custom ARAMIS sensors, which were successfully monitored from 3.5 miles away in the Firing Room at the Launch Control Center, during the 12 hour duration test. John Tyson and Tim Schmidt were given a NASA Team Award, and Tim Schmidt was awarded a Silver Snoopy for leadership of the External Tank Photogrammetry Teamt. The Silver Snoopy is the Astronaut’s personal achievement award.

Read More

Rocket Nozzle Hotfire Testing

"The ARAMIS data, as full-field image data, is intuitively understood. Image data is an ideal format for humans to understand. We analyze the ARAMIS results, and there are no arguments about the data, like we had with strain gauges; it is intuitively obvious what is occurring to our structures.” Dr. Paul Gradl, NASA Marshall Space Flight Center, testing hot fire rocket motors.

Read More

High Speed ARAMIS

Dynamic deformation measurement visualizes the behavior of aerodynamic structures in real use. During running operations, for example, real-time shape, vibration, acceleration, deformation and imbalance can be analyzed.

Trilion is an authorized reseller of Photron cameras, and has an agreement with Photron to be the sole source provider in the USA of Photron cameras for use with the Aramis digital image correlation system. Trilion has unique experience and capability to provide application-specific training and support for Photron cameras for high speed digital image correlation applications such as ballistic impact, bomb blast effect testing, crash testing, Hopkinson Bar testing, etc.

Trilion is also a reseller of Phantom, Fastec and Shimadzu cameras, and can readily import calibration and test images from any external camera stereo pair.

Read More